Raw material mill named Bailing

Raw material mill: 1.Both dry and wet grinding types available 3.Low energy consuming 4.ISO9001:2008 and 3c

Raw material mill are sent to enter the mills feed-in the moment the waste gas hot wind from the bottom of the suspending pre-heater kiln through the air intake is sent to enter that installation as well, where raw materials containing water starts to exchange heat. Raw materials are sent to the dryer where materials are gotten to be dry by intense heat exchange for the special spreading board within which spreads materials. Dry materials (still containing some water) pass the partition with the spreading board and enter the crudely milling cabin. Here raw materials are shattered by the grinders impacts and the grindings and further dried. Granule materials shattered to certain extents pass the grate to enter the middle unloading part, and then are ejected at exit cover with materials from refinedly milling cabin through the tubes unloading hole. The ejections are transmitted to powders selecting machine to divide. A few of divided crude powders pass the feed-in and then back to the crudely milling part a second time to increase the materials liquidity; while most of crude powders through the feed-in enter the refinedly milling cabin where crude powders are grinded more and further by grinders of small diameter and dried a second time by the mills hot wind through the feed-back at the same time. The new ejections conduct such circulation mentioned above one more time.

Main Technical Parameters:

No.	Product specifications (m)	Productivity (t / h)	Mill form	Transmission form	Power (kw)	Reducer		Weight	Weight
						Model	Ratio	(t)
1	φ2.2×7m	12-13	Lap -	Center	380	ZD70	5	54
2	φ2.4×7m	15-17	Lap -	Center	475	JR75	4.74	70.5
3	φ2.4×8m	16-18	Lap -	Center	475	JR75	4.74	78.5
4	φ3×9m	42-47	Lap -	Center	1000	MBY800	7.1	156.5	Excluding motor
5	φ3.2×9m	62-65	Lap -	Center	1250	MBY900	7.1	184.5	Excluding motor
6	φ3.8×7.5m	80	Lap -	Center	1600	JDX900	5.6	233
7	φ4.6×10+3.5m	190	Lap -	Center	3550	JQS3550	15.1	358
8	φ4.6×10.5+3.5m	210	Lap -	Center	3550	JQS3550	15.1	360

Model	Speed of bucket (r/min)	Weight of ball (t)	Size of feed opening (mm)	Size of output size (mm)	Production (t/h)	Power (kw)	Weight (t)
φ900×1800	38	1.5	≤20	0.075-0.89	0.65-2	18.5	3.6
φ900×3000	38	2.7	≤20	0.075-0.89	1.1-3.5	22	4.6
φ1200×2400	32	3.8	≤25	0.075-0.6	1.5-4.8	45	12.5
φ1200×3000	32	5	≤25	0.074-0.4	1.6-5	45	12.8
φ1200×4500	32	7	≤25	0.074-0.4	1.6-5.8	55	13.8
φ1500×3000	27	8	≤25	0.074-0.4	2-5	90	17
φ1500×4500	27	14	≤25	0.074-0.4	3-6	110	21
φ1500×5700	27	15	≤25	0.074-0.4	3.5-6	132	2407
φ1830×3000	24	11	≤25	0.074-0.4	4-10	180	28
φ1830×6400	24	23	≤25	0.074-0.4	6.5-15	210	34
φ1830×7000	24	25	≤25	0.074-0.4	7.5-17	245	36
φ2200×5500	21	30	≤25	0.074-0.4	10-22	370	48.5
φ2200×6500	21	30	≤25	0.074-0.4	14-26	380	52.8
φ2200×7500	21	33	≤25	0.074-0.4	16-29	475	56
φ2400×3000	20.6	15.5-15.6	≤25	0.074-0.4	15-55	245	59
φ2400×4500	21	30	≤25	0.074-0.4	15-60	380	65
φ2700×4000	20.6	40	≤25	0.074-0.4	20-80	400	94
φ2700×4500	20.7	48	≤25	0.074-0.4	20-90	430	102
φ3200×4500	18	65	≤25	0.074-0.4	According to different tech	800	137

Raw material mill named Bailing